DALI Phase dimmer 300W for DIN-EN 60715 TH35 rail mounting (DT4)

Item condition	New
Manufacture name	DALI Phase dimmer 300W for DIN-EN 60715 TH35 rail mounting (DT4)
Brand	ELTAKO
Categories	Switches
Country of origin	BG
Harmonized System Code	8542 3190 00
Assembly arrangement	Basic element
Method of operation	Other
Nominal voltage	230 V
Suitable for degree of protection (IP)	IP20
Device width	17.5 mm
Device height	98 mm
Device depth	56 mm
Max. switching power LED	300 W

Packing level 1

4010312324073, 4010312324073

Mounting method	DRA (DIN-rail adapter)
Colour	Grey
Halogen free	Yes
Connection type	Screwed terminal
Surface protection	Untreated
Material quality	Thermoplastic
Material	Plastic
Light value memory	Yes
Substation input	No
Serial dimmer	No
Applicable with movement sensor	No
Applicable with transmission button	No
Applicable with infrared button	No
Applicable with presence indicator	No
Applicable with button	No
Applicable with time switch/timer	No
Control voltage	9.5-22.5 V
Transparent	No
Surface finishing	Matt
Core cross section	0.5-2.5 mm²
IFTTT support available	No
Dimming phase cut-off	Yes
Dimming phase cut-on	Yes
App control via Bluetooth	No
Nominal power resistive load	300 W
Nominal power inductive load	300 VA
Nominal power capacitive load	300 VA
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Phase dimmer with DALI control input for DIN top-hat rails DIN-EN 60715 TH35. 98x17,5x56mm. Protection class IP20. Suitable for dimming 230V LED retrofit luminaries using DALI Converts DALI dimming level to a voltage with leading or trailing edge. The minimum dimming level (MIN LEVEL) is adjustable via DALI. Additional operating mode as switch (conforms to DT7) as from Firmware 3.5. The module represents a bus user and is therefore addressable. Double terminals for easy looping of the DALI bus. Dimming range 0.1%-100%. Supply voltage 230V AC. Output load range 10-300W. High efficiency. Configuration via DALI Cockpit PC software. Function: The DALI PD is an interface between classic dimming technology (phase dimming) and DALI which is based on the standard for DALI Control Gear (IEC 62386-102) and Device Type 4 equipment (IEC 62386-205). The DALI PD interface converts the required dimming level into a corresponding voltage signal with leading or trailing edge. Depending on the load the universal dimmer operates as a leading or trailing edge dimmer. The operating mode can be requested over DALI (DT4). The dimming characteristic is based on a logarithmic scale as stipulated in the DALI standard. The leading or trailing edge control supplies a sinusoidal voltage with a phase-cut on the leading or trailing edge. The PHYSICAL MINLEVEL is 3%. As of Firmware version 3.5 the DALI PD is equipped with an additional operating mode. It is switchable from DT4 operating mode (phase dimming) to DT7 (switch). In this operating mode the DALI PD acts as a switch. Its behaviour in this mode corresponds to the DALI standard for DT7 devices (IEC62386-208). In this operating mode the switch characteristic is determined by comparing the virtual dim level (VDAP) with 4 switching thresholds. The virtual dim level (VDAP) corresponds to the dim level of a DALI electronic ballast with its corresponding characteristics (limited by MINLEVEL and MAXLEVEL, dimming speed limited by fade time and fade rate). There are 2 switching thresholds in each dimming direction and they are used for comparison with the virtual dim level: A threshold with the value ‘MASK’ is inactive and is not used in the comparison. Switch-on/off delays can be implemented with fading. The device is powered from the DALI bus so that there is only partial support for the SYSTEM FAILURE LEVEL. On current devices (identified by Firmware > 4.0), you can choose between 0%,100% and MASK. On older models the SYSTEM FAILURE LEVEL is fixed - the 25W variant outputs 100%. The 300W variant outputs 0%.