Universal dimmer switch without N connection, especially for LED Power, MOSFET up to 200W

Item condition	New
Manufacture name	Universal dimmer switch without N connection, especially for LED Power, MOSFET up to 200W
Brand	ELTAKO
Categories	Switches
Country of origin	CN
Harmonized System Code	8536 5080 00
Assembly arrangement	Other
Method of operation	Touch control button
Type of load	Universal
Nominal voltage	230 V
Device width	45 mm
Device height	45 mm
Device depth	18 mm
Max. switching power LED	200 W

Packing level 1	4010312109618, 4010312109618
Packing level 2	4010312109618
Packing level 3	4010312109618

Mounting method	Flush mounted (plaster)
Colour	Blue
Halogen free	Yes
Connection type	Screwed terminal
Surface protection	Untreated
Material quality	Thermoplastic
Material	Plastic
Type of fastening	Mounting with screw
Light value memory	Yes
Substation input	No
Serial dimmer	No
Applicable with movement sensor	No
Applicable with transmission button	No
Applicable with infrared button	No
Applicable with presence indicator	No
Applicable with button	Yes
Applicable with time switch/timer	No
Control voltage	230 V
Transparent	No
Surface finishing	Matt
Core cross section	4 mm²
IFTTT support available	No
Dimming phase cut-off	Yes
Dimming phase cut-on	Yes
Min. depth of built-in installation box	18 mm
App control via Bluetooth	No
Nominal power resistive load	200 W
Nominal power capacitive load	200 VA
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Without N connection, POWER MOSFET up to 200W. Standby loss 0.5 watt only. With control inputs for pushbutton light switches and light switches. With adjustable minimum brightness, dimming technology and dimming speed. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimmer switch for R and C loads up to 200W, depending on ventilation conditions. Dimmable 230V LED lamps and energy saving lamps ESL in trailing edge mode up to 200W or up to 40W in leading edge mode, depending on ventilation conditions. If 230V LED lamps are lightly glowing when they are turned off, a GLE base load must be installed parallel to the lamp. It is not permited to connect L loads (inductive loads, like wounded transfomers). Zero passage switching with soft start and soft OFF to protect lamps. Control voltage, supply ­voltage and switching voltage 230V. Min. load 4W. Short-time control commands switch on/off, permanent control varies the brightness up to the maximum level. A short interruption of control changes the direction of dimming. The brightness level is stored after switching off (memory). It is possible to deactivate the memory function by turning 3 times the upper rotary switch to the right stop (max), then it is compatible with ESL. To re­activate the memory function (factory setting), turn the upper rotary switch 3 times to the left stop (min). In case of a power failure the switching position and the brightness level are stored, and will switch on after the failure if applicable. Automatic electronic overload protection and over-temperature switch-off. The minimum brightness level (completely dimmed down) can be adjusted with the upper rotary switch %lamp. The lower rotary switch allows to choose between the both dimming technologies, P-AN leading or P-AB trailing edge and to change the dimming speed. Simultaneously the duration of soft on and soft off will be adjusted. If light switches cannot be replaced by pushbutton light switches, there is a separate control input for light switches: If the switch is opened briefly after closing, the light is dimmed until the next time it is opened again briefly. The dimming direction changes automatically at both peaks. The dimming direction can also be changed by opening the switch briefly twice. Switching operation for children's rooms (only if controlled by pushbutton light switch): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (only if controlled by pushbutton light switch): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Without N connection, therefore suitable for mounting directly behind the pushbutton light switch or light switch, even if no N wire is available.