RS485 bus actuator 2-speed fan relay

Item condition	New
Manufacture name	RS485 bus actuator 2-speed fan relay
Brand	ELTAKO
Categories	Switches
Country of origin	CN
Harmonized System Code	8526 9200 00
Mounting method	Other
Colour	Grey
Halogen free	Yes
Surface protection	Other
Current supply	Other
Number of relays	2
Suitable for switch	Yes
Suitable for pulse button	Yes
Suitable for dimmer	No
Suitable for roller shutter switch	No
Material quality	Thermoplastic
Material	Plastic
Type of fastening	Other
Rolling code system	-
Radio frequency	868 MHz
In housing	Yes
In tube base housing	No
Printed circuit board/module	No
Push button mode	Yes
Switching mode	Yes
With manual radio transmitter	No
With radio coding device	No
With radio controlled push button	No
Suitable for venetian-/roller shutter switch	No
Suitable for venetian shutter switch	No
Transparent	No
Surface finishing	Matt
Suitable for degree of protection (IP)	IP20
IFTTT support available	No
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Packing level 1	4010312316160, 4010312316160
Packing level 2	4010312316160
Packing level 3	4010312316160

2-speed fan relay, 1+1 NO contacts potential free 16A/250V AC, with DX tech­nology. Bidirectional. Only 0.1 watt standby loss. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. Connection to the Eltako-RS485 bus. Bus cross wiring and power supply with jumper. Patented Eltako Duplex technology allows you to switch normally potential free contacts in zero passage switching when 230V A/C voltage 50Hz is switched. This drastically reduces wear. To achieve this, simply connect the N conductor to the terminal (N1) and L to 1(L) and/or N to (N2) and L to 3(L). This ­results in an additional standby consumption of only 0.1 watt. If supply voltage fails, the switching state is retained. When supply voltage is ­restored, the device is switched off in defined mode. This fan relay evaluates the information of up to 23 passive sensors, e.g. wireless pushbuttons, window/door contacts, window handle sensors FFG7B-rw or wireless transmitter modules. Active sensors for CO2, air quality, humidity and temperature are also evaluated. Several active sensors can be linked by the PCT14 PC Tool. When the two contacts are switched in parallel, the 2-speed actuator for 2 fan speeds becomes an actuator for one fan. The middle rotary switch must be set to position LRN for teach-in. Set the required operating mode when the fan actuator is in operation. During the teach-in process, adjust the upper rotary switch to set the sensor type. A wireless pushbutton (exclusive) with double rocker is taught-in in rotary switch position 1. Double rockers are assigned automatically: top left Stage 1 (only contact 1-2 closed), top right stage 2 (only contact 3-4 closed). Bottom left and bottom right OFF: both contacts open. A wireless pushbutton (adding) with double rocker is taught-in in rotary switch position 2. Double rockers are assigned automatically: top left stage 1 (contact 1-2 closed), top right Stage 2 (contacts 1-2 and 3-4 closed). Bottom left and bottom right OFF: both contacts open. If you switch the two contacts in parallel, one wireless pushbutton and 1 rocker are sufficient. In this case, top is ON and bottom is OFF. In rotary switch position 3, teach in ON/OFF switch with double rocker (all rockers are assigned automatically) and wireless transmitter modules When you teach in an FTK device, window handle sensor FFG7B-rw or active sensor, there is no need to take the teach-in position into account. When operated with an active sensor, set the switch-in threshold on the lower rotary switch. When the threshold is reached, Stage 1 (Contact 1-2) is switched on. At the upper rotary switch, set the addition value at which Stage 2 (Contact 3-4). Turn the middle rotary switch to set one of the operating modes AUTO1 to AUTO7. AUTO1: for manual mode of a 2-stage fan by means of a double rocker wireless pushbutton. Each contact is closed separately (exclusive) or contact 3-4 cuts in to switch stage 2 (accumulative). This is determined when teaching-in. Passive sensors, such as wireless pushbuttons and transmitter modules, which are taught-in as a off-switches, cause opening of both contacts. As long as the control voltage is applied to transmitter modules or a window monitored by an FTK or window handle sensor FFG7B-rw is open, the contacts are open and can not be switched on manually. AUTO2: Activating with either a wireless CO2 or air quality sensor. The switch-on thresholds are set by the lower and upper rotary switches. The contacts close exclusively. AUTO3: Activating with wireless CO2 sensor. The switch-on thresholds are set by the lower and upper rotary switches. The contacts close exclusively. AUTO4: Same as AUTO2, but activated by the wireless temperature sensor. AUTO5: Same as AUTO2, but the contacts close adding. AUTO6: Same as AUTO3, but the contacts close adding. AUTO7: Same as AUTO4, but the contacts close adding. Overview of switch-on thresholds for CO2, air quality, humidity and temperature see operating instructions. The LED below the upper function rotary switch performs during the teach-in process according to the operating ­instructions. It shows control commands by short flickering during operation.