Wireless actuator universal dimmer switch 30100835

Item condition	New
Manufacture name	Wireless actuator universal dimmer switch 30100835
Brand	ELTAKO
Categories	Switches
Country of origin	CN
Harmonized System Code	8526 9200 00
Mounting method	Flush mounted (plaster)
Colour	Blue
Halogen free	Yes
Surface protection	Other
Current supply	230 V AC
Suitable for switch	No
Suitable for pulse button	No
Suitable for dimmer	Yes
Suitable for roller shutter switch	No
Material quality	Thermoplastic
Material	Plastic
Type of fastening	Other
Rolling code system	Yes
Number of commands	32
Radio frequency	868 MHz
In housing	Yes
In tube base housing	No
Printed circuit board/module	No
Push button mode	Yes
Switching mode	No
With manual radio transmitter	No
With radio coding device	No
With radio controlled push button	No
Suitable for venetian-/roller shutter switch	No
Suitable for venetian shutter switch	No
Transparent	No
Surface finishing	Matt
Suitable for degree of protection (IP)	IP20
IFTTT support available	No
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Packing level 1	4010312300299, 4010312300299
Packing level 2	4010312300299
Packing level 3	4010312300299

Universal dimmer switch, 300W power MOSFET. Automatic lamp detection. Only 0.7 watt standby loss. With adjustable minimum brightness or dimming speed. With switching operation for light alarm clocks, children's rooms and snooze function. Additionally with light scene control. Encrypted wireless, bidirectional wireless and repeater function are switchable. For installation. 45mm long, 45mm wide, 33mm deep. Universal dimmer switch for lamps up to 300W, dependent on ventilation conditions. Dimmable 230V-LED lamps and dimmable energy saving lamps ESL, additionally dependent on the lamps electronics and the dimming technology. Zero passage switching with soft ON and soft OFF to protect lamps. Supply voltage, switching voltage and control voltage local 230V. No minimum load. The brightness level is stored on switch-off (memory). In case of a power failure the switch position and the brightness stage are stored and may be switched on when the power supply is restored. Automatic electronic overload protection and overtemperature switch-off. You can teach in encrypted sensors. You can switch on bidirectional wireless and/or a repeater function. Every change in state and incoming central command telegrams are then confirmed by a wireless telegram. This wireless telegram can be taught into other actuators like the FSR61NP-230V, universal displays and Professional Smart Home controller. The current dimming value is also displayed in % in the respective app. The minimum brightness (fully dimmed) or the dimming speed is adjustable with the upper %/dimming speed rotary switch. The lower rotary switch determines the operation, whether the automatic lamp detection or special comfort positions should act: AUTO allows the dimming of all light species. LC1 is a comfort position for dimmable 230V LED lamps which are not being dimmed down enough when set to AUTO (trailing phase angle) dependent on the construction and must therefore be forced to leading phase angle. LC2 and LC3 are comfort positions for dimmable 230V LED lamps like LC1, but with different dimming curves. EC1 is a comfort position for energy saving lamps which must be switched on with increased power dependent on the construction, so they will also switch on again safely in cold condition when ­dimmed down. EC2 is a comfort position for energy saving lamps which will not be switched on again when dimmed down dependent on the construction. Memory is switched off in this position. In positions LC1, LC2, LC3, EC1 and EC2 no inductive (wound) transformers should be used. In addition, the maximum number of dimmable LED lamps can be lower than in the AUTO ­position dependent on the construction. The pushbuttons can be either taught-in as direction pushbuttons or universal pushbuttons: As direction pushbutton switch on and dim up is on one side and switch off and dim down on the other side. A double-click on the switch on side triggers the automatic dimming up to full brightness with dim speed time. A double-click on the switch off side triggers the snooze function. The children's room function is triggered on the switch on side. As a universal pushbutton the direction change is made by briefly releasing the pushbutton. For light scene control, light alarm circuit, children's room circuit and sleep timer, refer to the operator manual. The LED performs during the teach-in process according to the operating instructions. It shows wireless control commands by short flickering during operation.