Universal dimmer switch, Power MOSFET up to 400W

Состояние товара	Новый
Название производителя	Universal dimmer switch, Power MOSFET up to 400W
Бренд	ELTAKO
Категории	Выключатели
Страна происхождения	CN
Код гармонизированной системы	8536 5080 00
Устройство сборки	Другое
Метод работы	Сенсорная кнопка управления
Тип нагрузки	Универсальный
Номинальное напряжение	230 V
Ширина устройства	45 mm
Высота устройства	45 mm
Глубина устройства	18 mm
Макс. светодиодный индикатор питания	400 W

Уровень упаковки 1	4010312107874, 4010312107874
Уровень упаковки 2	4010312107874
Уровень упаковки 3	4010312107874

Способ крепления	Монтаж заподлицо (штукатурка)
Цвет	Синий
Без галогена	Yes
Тип соединения	Винтовая клемма
Защита поверхности	Другое
Качество материала	Термопластик
Материал	Пластик
Тип крепления	Крепление с винтом
Память светового значения	Yes
Вход подстанции	No
Серийный диммер	No
Применяется с датчиком движения	No
Применимо с кнопкой передачи	No
Применимо с инфракрасной кнопкой	No
Применяется с индикатором присутствия	No
Применимо с кнопкой	Yes
Применимо с таймером/таймером	No
Управляющее напряжение	8-230 V
Прозрачный	No
Отделка поверхности	Матовый
Сечение жилы	4 mm²
Доступна поддержка IFTTT	No
Отсечка фазы диммирования	Yes
Отключение фазы диммирования	Yes
Мин. глубина встроенной монтажной коробки	18 mm
Управление приложением через Bluetooth	No
Номинальная мощность активной нагрузки	400 W
Номинальная мощность индуктивной нагрузки	400 VA
Номинальная мощность емкостной нагрузки	400 VA
Совместимость с Apple HomeKit	No
Совместимость с Google Ассистент	No
Совместимость с Amazon Alexa	No

Universal dimmer switch. Power MOSFET up to 400W. Automatic lamp detection. Standby loss 0.1 watt only. With adjustable minimum brightness or dimming speed. With switching operation for children's rooms and snooze function. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimmer switch for lamps up to 400 watts, depending on ventilation conditions. Dimmable 230V LED lamps and dimmable energy saving lamps ESL dependent on the lamps electronics and the dimming technology. Zero passage switching with soft start and soft OFF to protect lamps. Universal control voltage input 8 to 230V UC, electrically isolated from the 230V supply voltage and switching voltage. No minimum load required. Short-time control commands switch on/off, permanent control varies the brightness to the maximum level. An interruption of control changes the direction of dimming. The setting of the brightness level is stored after switching off (Memory). In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. Automatic electronic overload protection and over-temperature switch-off. With the top rotary switch %lamp/dim speed either the minimum brightness level (completely dimmed down) or the dim speed can be adjusted. The duration of soft-on and soft-off will be changed with the dimming speed. In operation, the bottom rotary switch determines, whether automatic lamp detection or special comfort positions should operate: AUTO allows the dimming of all lamp types. LC1 is a comfort position for dimmable 230V LED lamps which are not being dimmed down enough when set to AUTO (trailing phase angle) dependent on the construction and must therefore be forced to leading phase angle. LC2 and LC3 are comfort positions for dimmable 230V LED lamps like LC1, but with different dimming curves. EC1 is a comfort position for energy saving lamps which must be switched on with increased power dependent on the construction, so they will also switch on again safely in cold condition when dimmed down. EC2 is a comfort position for energy saving lamps which will not be switched on again when dimmed down dependent on the construction. Memory is switched off in this position. In positions LC1, LC2, LC3, EC1 and EC2 no inductive (wound) transformers should be used. In addition, the maximum number of dimmable LED lamps can be lower than in the AUTO position dependent on the construction. With special switching operation for children's rooms: If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function: With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Mixing of L loads (inductive loads, e.g. wound transformers) and C loads (capacitive loads, e.g. electronic transformers) is not permitted. R loads (ohmic loads, e.g. 230V incandescent lamps and halogen lamps) may be added anytime.