Wireless actuator PWM LED dimmer switch, 12-36V DC up to 4A

Состояние товара	Новый
Название производителя	Wireless actuator PWM LED dimmer switch, 12-36V DC up to 4A
Бренд	ELTAKO
Категории	Датчики
Страна происхождения	CN
Код гармонизированной системы	8526 9200 00
Способ крепления	Монтаж на поверхность (штукатурка)
Модель	Привод регулировки яркости
Количество выходов	1
Частота	50 Hz
Шинная система KNX	No
Шинная система радио частая	Yes
Шинная система Powernet	No
С автобусным сообщением	No
Тип нагрузки	Емкостной
Напряжение	36-12 V
Другие автобусные системы	Нет
Шинная система LON	No
Вход подстанции	No
Возможно параллельное обслуживание	No
Локальное управление/ручное управление	No
Выходная мощность	144 W
Степень защиты (IP)	IP20
со светодиодной индикацией	No
Повышение мощности подходит	No
Шинная система Радио KNX	No
Радио частый двунаправленный	Yes
Модуль шины съемный	No
Мин. глубина встроенной монтажной коробки	33 mm

Уровень упаковки 1	4010312315255, 4010312315255
Уровень упаковки 2	4010312315255
Уровень упаковки 3	4010312315255

PWM LED dimmer switch for LEDs 12-36V DC, up to 4A. Only 0.2-0.4 watt stand­by loss. With adjustable minimum bright­ness and dimming speed. With ­switching operation for children's rooms and snooze function. Also with light scene control by PC or wireless pushbuttons. Encrypted wireless, bi­directional wireless and repeater function are switchable. For installation. 45mm long, 45mm wide, 33mm deep. Supply voltage 12 to 36V DC, depending on the connected LED lighting. Output voltage PWM (puls width modulation). Maximum output voltage 4A. A pulse resistant DC power supply unit is required, which provides the necessary voltage and required current of the LED light(s). Universal control voltage input 8 to 230V UC, electrically isolated from the 230 V supply voltage and switching voltage. The brightness level is stored on switch-off (memory). In case of a power failure the switch position and the brightness stage are stored and may be switched on when the power supply is restored. Automatic electronic overload protection and overtemperature switch-off. You can teach in encrypted sensors. You can switch on bidirectional wireless and/or a repeater function. The minimum brightness (fully dimmed) is adjustable with the upper %lamp rotary switch. In the setting LRN up to 35 pushbuttons can be assigned, of which one or more central pushbuttons. The dimming speed can be adjusted with the lower dimming speed rotary switch. In addition to the wireless control input via an internal antenna, this universal dimmer switch can also be controlled locally by a conventional 230V control switch if fitted previously. A short interruption of control changes the direction of dimming. Short control commands switch on/off. The pushbuttons can be either taught-in as direction pushbuttons or universal pushbuttons: As direction pushbutton switch on and dim up is on one side and switch off and dim down on the other side. A double-click on the switch on side triggers the automatic dimming up to full brightness with dim speed time. A double-click on the switch off side triggers the snooze function. The children's room function is triggered on the switch on side. As a universal pushbutton the direction change is made by briefly ­releasing the pushbutton. Central pushbutton on switches on with memory value. Central pushbutton off switches off. Switching operation for children's rooms (universal pushbutton or direction pushbutton on the switch-on side): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (universal pushbutton or direction pushbutton on the switch-off side): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Light scenes via app are set and re­trieved using the Professional Smart Home controller. Lights scenes with wireless pushbuttons are taught in on the FLD61 device. Up to four brightness values which can be taught-in in light scene pushbuttons with double rocker. A FBH can either be taught-in as a movement detector with/without twilight switch or a FAH as a twilight switch according to the operating instructions. The LED performs during the teach-in process according to the operating instructions. It shows wireless control commands by short flickering during operation.