Wireless actuator multifunction time relay

Состояние товара	Новый
Название производителя	Wireless actuator multifunction time relay
Бренд	ELTAKO
Категории	Выключатели
Страна происхождения	CN
Код гармонизированной системы	8526 9200 00
Способ крепления	Монтаж заподлицо (штукатурка)
Цвет	Синий
Без галогена	Yes
Защита поверхности	Другое
Текущее предложение	230 В ПЕРЕМЕННОГО ТОКА
Количество реле	1
Подходит для переключателя	Yes
Подходит для импульсной кнопки	Yes
Подходит для диммера	No
Подходит для выключателя рольставни	No
Качество материала	Термопластик
Материал	Пластик
Тип крепления	Другое
Система скользящего кода	Yes
Количество команд	32
Радиочастота	868 MHz
В жилье	Yes
В корпусе трубчатого основания	No
Печатная плата/модуль	No
Режим кнопки	Yes
Режим переключения	Yes
С ручным радиопередатчиком	No
С радиокодирующим устройством	No
С радиоуправляемой кнопкой	No
Подходит для переключателя жалюзи/жалюзи	No
Подходит для венецианского выключателя жалюзи	No
Прозрачный	No
Отделка поверхности	Матовый
Подходит для степени защиты (IP)	IP20
Доступна поддержка IFTTT	No
Совместимость с Apple HomeKit	No
Совместимость с Google Ассистент	No
Совместимость с Amazon Alexa	No

Уровень упаковки 1	4010312302293, 4010312302293
Уровень упаковки 2	4010312302293
Уровень упаковки 3	4010312302293

1 NO contact potential free 10A/250V AC, 230V LED lamps up to 400W, incandescent lamps up to 2000 watts.* Encrypted wireless, bidirectional wireless and repeater ­function are switchable. Only 0.8 watt standby loss. For installation. 45mm long, 45mm wide, 33mm deep. Supply voltage and if necessary control voltage locally 230V. If a power failure occurs, the switching state is retained. If a power failure occurs repeatedly, the device is switched off in a defined sequence. This wireless actuator features state-of-the-art hybrid technology that we developed: we combined the wear-free receiver and evaluation electronics with a bistable relay. By using a bistable relay coil power loss and heating is avoided even in the on mode. After installation, wait for short automatic synchronisation before the switched consumer is connected to the mains. In addition to the wireless control input via an internal antenna, this wireless actuator can also be controlled locally by a conventional control switch if fitted previously. Glow lamp current is not permitted. You can teach in encrypted sensors. You can switch on bidirectional wireless and/or a repeater function. Every change in state and incoming central command telegrams are confirmed by a wireless telegram. This wireless telegram can be taught-in in other actuators, Professional Smart Home controllers and in universal displays. With the top rotary switch in the setting LRN up to 35 wireless pushbuttons can be ­assigned, of which one or more central control pushbuttons. In addition, wireless window/door contacts (FTK) may have a NO or NC function when the window is open. If a direction pushbutton is taught-in, a function (e.g. TI) can be started using the top key (START) and stopped with the bottom key (STOP). The required function can then be selected. Switching will be visualised by flashing of the LED. RV = off delay. AV = operating delay. TI = clock generator starting with impulse. IA = impulse-controlled operating delay. EW = fleeting NO contact. The bottom rotary switch sets the time from 0.5 seconds to 60 minutes. The LED performs during the teach-in process according to the operating instructions. It shows wireless control commands by short flickering during operation. * The maximum load can be used from a delay time or clock cycle of 5 minutes. The maximum load is reduced for shorter times as follows: up to 2 minutes 30%, up to 5 minutes 60%.